HP Scanner makes everything yellow (HP Scanjet 2400)

[Sonnich Jensen]

Hi

Here are some pictures:
Loading Image...
Loading Image...

A is the original picture, 50% in order to make it fit here.
As you can see only a part of it is in the right colours.

A part of the original scan is the B - with "waves" in it, I have seen
that before and know simply to resize. But you can see the colour
difference better.

What causes the yellowness and how can I fix it?

It is a HP Scanjet 2400.

WBR
Sonnich

[isw]

In article

Post by Sonnich Jensen
Hi
http://hot.ee/sonnich/scan1a.jpg
http://hot.ee/sonnich/scan1b.jpg
A is the original picture, 50% in order to make it fit here.
As you can see only a part of it is in the right colours.
A part of the original scan is the B - with "waves" in it, I have seen
that before and know simply to resize. But you can see the colour
difference better.
What causes the yellowness and how can I fix it?

It looks like the signal from the "blue" sensor is intermittent --
except for that stripe halfway down, it's not getting through. This is
probably due to a loose connector, a broken wire or failed solder joint,
but possibly something else. In any case, the break is inside the
scanner, very possibly in or around the flexible cable that connects to
the traveling scan head.

If you can get the scanner apart, a close visual inspection might
indicate how it could be fixed.

Isaac

[Sonnich Jensen]

Post by isw
In article

Post by Sonnich Jensen
Hi
http://hot.ee/sonnich/scan1a.jpg
http://hot.ee/sonnich/scan1b.jpg
A is the original picture, 50% in order to make it fit here.
As you can see only a part of it is in the right colours.
A part of the original scan is the B - with "waves" in it, I have seen
that before and know simply to resize. But you can see the colour
difference better.
What causes the yellowness and how can I fix it?

It looks like the signal from the "blue" sensor is intermittent --
except for that stripe halfway down, it's not getting through. This is
probably due to a loose connector, a broken wire or failed solder joint,
but possibly something else. In any case, the break is inside the
scanner, very possibly in or around the flexible cable that connects to
the traveling scan head.
If you can get the scanner apart, a close visual inspection might
indicate how it could be fixed.

I just found that. I can see that the cable i used, hence every 1,5 cm
it seems to be broken - and there truely is one broken connection.
I will try with a single wire, solder it on both ends.
But are such cables available?
Or should I take an old HD flat cable and older that on?

Sonnich

[Paul]

Post by Sonnich Jensen

Post by isw
In article

Post by Sonnich Jensen
Hi
http://hot.ee/sonnich/scan1a.jpg
http://hot.ee/sonnich/scan1b.jpg
A is the original picture, 50% in order to make it fit here.
As you can see only a part of it is in the right colours.
A part of the original scan is the B - with "waves" in it, I have seen
that before and know simply to resize. But you can see the colour
difference better.
What causes the yellowness and how can I fix it?

It looks like the signal from the "blue" sensor is intermittent --
except for that stripe halfway down, it's not getting through. This is
probably due to a loose connector, a broken wire or failed solder joint,
but possibly something else. In any case, the break is inside the
scanner, very possibly in or around the flexible cable that connects to
the traveling scan head.
If you can get the scanner apart, a close visual inspection might
indicate how it could be fixed.

I just found that. I can see that the cable i used, hence every 1,5 cm
it seems to be broken - and there truely is one broken connection.
I will try with a single wire, solder it on both ends.
But are such cables available?
Or should I take an old HD flat cable and older that on?
Sonnich

The cable could be made of Kapton (Polyimide), and designed to be
flexed over and over again. You'd want to look for "flex cable",
rather than regular ribbon cable. The solid wires in regular ribbon cable
would snap after a relatively small number of flexure cycles.

http://en.wikipedia.org/wiki/Flexible_electronics

http://en.wikipedia.org/wiki/Flexible_flat_cable

The cables can be affixed by compression. Some people at work
tried soldering to make repairs, but the results were a mess.
Those cables only work well, with their "native" attach method
(the connector provided with the cabling). Home repair is more
difficult.

http://www.molex.com/molex/products/group?key=ffc_fpc_connectors&channel=PRODUCTS

Paul

[Sonnich Jensen]

Post by Paul

Post by Sonnich Jensen

Post by isw
In article

Post by Sonnich Jensen
Hi
http://hot.ee/sonnich/scan1a.jpg
http://hot.ee/sonnich/scan1b.jpg
A is the original picture, 50% in order to make it fit here.
As you can see only a part of it is in the right colours.
A part of the original scan is the B - with "waves" in it, I have seen
that before and know simply to resize. But you can see the colour
difference better.
What causes the yellowness and how can I fix it?

It looks like the signal from the "blue" sensor is intermittent --
except for that stripe halfway down, it's not getting through. This is
probably due to a loose connector, a broken wire or failed solder joint,
but possibly something else. In any case, the break is inside the
scanner, very possibly in or around the flexible cable that connects to
the traveling scan head.
If you can get the scanner apart, a close visual inspection might
indicate how it could be fixed.

I just found that. I can see that the cable i used, hence every 1,5 cm
it seems to be broken - and there truely is one broken connection.
I will try with a single wire, solder it on both ends.
But are such cables available?
Or should I take an old HD flat cable and older that on?
Sonnich

The cable could be made of Kapton (Polyimide), and designed to be
flexed over and over again. You'd want to look for "flex cable",
rather than regular ribbon cable. The solid wires in regular ribbon cable
would snap after a relatively small number of flexure cycles.
http://en.wikipedia.org/wiki/Flexible_electronics
http://en.wikipedia.org/wiki/Flexible_flat_cable
The cables can be affixed by compression. Some people at work
tried soldering to make repairs, but the results were a mess.
Those cables only work well, with their "native" attach method
(the connector provided with the cabling). Home repair is more
difficult.
http://www.molex.com/molex/products/group?key=ffc_fpc_connectors&chan...

Makes me wonder do ordinary electronics shops sell those?
At some point a selection of those would meet most peoples need. I
will try the 2 local dealers (Elfa and another)

Sonnich

[Sonnich Jensen]

Post by isw
In article

Post by Sonnich Jensen
Hi
http://hot.ee/sonnich/scan1a.jpg
http://hot.ee/sonnich/scan1b.jpg
A is the original picture, 50% in order to make it fit here.
As you can see only a part of it is in the right colours.
A part of the original scan is the B - with "waves" in it, I have seen
that before and know simply to resize. But you can see the colour
difference better.
What causes the yellowness and how can I fix it?

It looks like the signal from the "blue" sensor is intermittent --
except for that stripe halfway down, it's not getting through. This is
probably due to a loose connector, a broken wire or failed solder joint,
but possibly something else. In any case, the break is inside the
scanner, very possibly in or around the flexible cable that connects to
the traveling scan head.
If you can get the scanner apart, a close visual inspection might
indicate how it could be fixed.

My scanner now has an additional wire and works well.

The wire moves behind the head, and does not get stuck. Maybe not the
best option, but it does the trick

Sonnich